SPECIFIC REQUIREMENTS · ACTUAL LESSON ACTIONS For manufacturing safety teams, Controls Trainer connects specific safety requirements to actions employees can practice. Here are five examples from the actual lessons. 29 CFR 1910.333(b)(2)(ii)(B) and (iii)(A) OSHA nineteen ten point three three three requires electrical isolation, with locks and tags on the disconnecting means. A Stop button is not a substitute. 29 CFR 1910.333(b)(2)(iii)(A) and (iv)(B) In Level One, the learner opens the main disconnect and applies a personal lock and tag. Wiring stays locked until the lesson's electrical safety checks are complete. NFPA 70E (2024), 120.6(7) NFPA seventy E, twenty twenty-four, section one twenty point six, step seven, calls for testing at each point of work and verifying the tester before and after. NFPA 70E (2024), 120.6(7) · 29 CFR 1910.333(b)(2)(iv)(B) Our electrical lessons teach that sequence with a simulated meter. Prove it on a known source, test the required circuit points, then prove it again. The incoming line side can still be live. 29 CFR 1910.333(b)(2)(iv)(B) · NFPA 70E (2024), 120.6(7) The OSHA verification requirement calls for a qualified person to test the electrical parts that employees could contact. In the lesson, one zero reading does not complete the verification. The learner must check the required points and complete the meter-proving sequence. 29 CFR 1910.333(b)(2)(ii)(C) OSHA's electrical work rule also addresses hazardous stored electrical energy. Level Four demonstrates this with the drive's D C bus. Switching off the supply does not instantly discharge it. Learners wait and check the simulated voltage; real servicing follows the manufacturer's discharge and testing instructions. 29 CFR 1910.147(d)(5)(i) and (d)(6) OSHA nineteen ten point one four seven requires hazardous stored energy to be controlled and isolation verified before servicing. 29 CFR 1910.147(d)(5)(i) and (d)(6) In Level Five, learners support the vertical axis, secure the part, isolate the air, and check the downstream pressures. Electrical power off does not remove pneumatic or gravity hazards. 29 CFR 1910.147(d)(5)(ii) Stored energy can also return. OSHA nineteen ten point one four seven requires continued verification where hazardous energy could reaccumulate. Level Five teaches checks of separate air volumes and pressure returning, while mechanical support controls the vertical load. 29 CFR 1910.303(b)(3) OSHA nineteen ten point three zero three requires completed wiring to be free of unintended shorts and grounds. Level One teaches circuit connections through labeled terminals, with checks against the required wiring. 29 CFR 1910.304(g)(5) The wiring exercise also distinguishes protective earth from the twenty-four-volt circuit return. OSHA nineteen ten point three zero four requires an effective, continuous grounding path. The simulated connections introduce that principle; they do not replace installation design, conductor sizing, or physical inspection. 29 CFR 1910.212(a)(1) OSHA nineteen ten point two one two requires protection from machine hazards. Level Ten asks learners to identify hazards and select suitable safeguards. 29 CFR 1910.212(a)(1) · Guard-function training example In Level Six, they can open the simulated guard and observe the machine stop. They then practice restoring the guard and resetting the safety circuit before a deliberate restart. 29 CFR 1910.212(a)(1) · Lesson-specific functional checks The Level Ten review connects conveyor nip points, rotating equipment, and pneumatic movement to specific safeguards. Level Six reinforces the difference between resetting a safety circuit and commanding motion. Testing the simulation supports understanding; real machine safeguarding still requires equipment-specific assessment and validation. controlstrainer.com/compliance.php Specific requirements. Repetitive safety practice. Use Controls Trainer alongside your plant procedures and practical evaluation. Explore the lessons and cited references at Controls Trainer dot com slash compliance.